Create a fan model
Fan-shaped models can be created in the Spin Wizard or Extrusion Wizard.
The operation procedure is as follows:
The operation procedure is as follows:
How to create in the Spin Wizard
[1] Run the Feature tab → Feature Group → Spin Wizard and draw a rectangle.
[2] Double-click the corner restraint mark to enable right-angle restraint.
Red is detained.
Red is detained.
[3] [Sketch] tab → [Detention] group → [SmartDimension]Enter the dimensions of inner diameter, outer diameter, and thickness and finish the sketch.
[4] After creating the model, change the opening angle.
In the (yellow highlighted) state of IntelliShape,Right-click the handle for the rotation angle of the spin and select Edit Value.
Enter any angle and click OK.
In the (yellow highlighted) state of IntelliShape,Right-click the handle for the rotation angle of the spin and select Edit Value.
Enter any angle and click OK.
[5] Again, in the (yellow highlighted) state of IntelliShape, you can double-click on the dimensions to change the inner diameter, outer shape, and thickness.
See also:Spin Wizard - IRONCAD User's Guide
How to create in Extrusion Wizard
[1] [Feature] Tab →Run Feature Group → Extrusion Wizard.
[2] Draw the inner diameter and outer diameter in the Sketch tab → Drawing Group → Center, Radius.
[3] [Sketch] tab→ Draw an opening angle in Drawing Group → Two Point, and delete unnecessary lines in the Sketch tab → Edit Group → Trim.
[4] Double-click the restraint mark to enable corner vertical and horizontal restraint.
Red is detained.
[5] [Sketch] tabEnable concentricity in the [Binding] group → [Centricity] inner diameter and outer diameter concentricity.
The figure below shows that the concentricity is valid.
[6] [Sketch] tab→ Enter the dimensions of the inner diameter, outer diameter, and opening angle in the [Binding] group → [SmartDimension] and exit the sketch.
[7] You can change the extrusion distance and change the thickness.
In the (yellow highlighted) state of IntelliShape, you can change the thickness by dragging the handle.
In the (yellow highlighted) state of IntelliShape, you can change the thickness by dragging the handle.
[8] Similarly,In the (yellow highlighted) state of IntelliShape, you can change the inner diameter, outer diameter, and opening angle.
You can double-click the dimensions and change them.
If you forgot to enter the dimensions, you can right-click on IntelliShape (highlighted in yellow) and add them in Edit Cross Section Shape.
For more information, please refer to the video below.
IC-011
Related Articles
Create a chuck opening and closing action
Explain how to create a chuck movement to grab the workpiece. Even if the number of chuck points or more, if it is the same opening and closing operation, you can create a movement by copying one chuck in a circular array. Please refer to the ...Create a rectangular pyramid
[Shape] Catalog [PyramidsThen you can create a pyramid. However, rectangular pyramids cannot be created. Rectangular pyramids can be created in the Extrusion Wizard. The operation procedure is as follows: [1] Create a block in the Feature tab → ...Create grooves with sweeps on cylindrical sides
The cylindrical shape explains how to create a groove through which the cam passes. The groove is created vertically towards the center of the cylinder. Procedures [1] Create guidelines wrapped in cylindrical shapes. [2] Create a cross-sectional ...Create a stand with a structure part
Explain how to create a rack using structure parts. By creating with structure parts, you can create a stand that is easy to resize. Procedures [1] Right-click Block from the Shape catalog, drag and drop, and select Drop as a Structure Part. ...Set the auxiliary sign of the surface shape to the welding sign
by CAXA Draft.Explain how to set a surface shape auxiliary sign for welding sign. Procedures Select [1] Note tab → Welding Symbol. [2] Set the opening sign. Initially, it is None, so select any symbol from the list on the right. [3] [Open sign] in ...